![how to enable web access to brocade san switch how to enable web access to brocade san switch](https://1.bp.blogspot.com/-nPB5NKDwoSA/T2tLSUT_YiI/AAAAAAAAADI/vQuTwsr6MM0/s1600/Picture16.png)
- #How to enable web access to brocade san switch how to#
- #How to enable web access to brocade san switch windows 10#
Leave the security at high but don’t forget to add the IP addresses of your Brocade switch to the Exception Site List. Make sure Enable Java Content in the browser is enabled. You need to go to Java configuration and select the Security Tab.
#How to enable web access to brocade san switch windows 10#
Below is a screenshot of my Windows 10 or Windows Server 2016 (Desktop Experience) management station.īut we’re not there yet. On the management station, I add them to the desktop for easy access.
![how to enable web access to brocade san switch how to enable web access to brocade san switch](https://www.ibm.com/support/pages/system/files/support/swg/tivtech.nsf/0/9bbfe57edaba080e8525824300509c07/Content/0.2D4.gif)
I just place then under C:\Programdata\BrocadeFC for safe keeping together with a cop of the short cuts. I actually created some ico files based on an image of brocades Fibre Channel switches that I use for this. I normally change the icon to the shortcut to indicate it’s pointing to a network device. Instead of navigating to http or https to just the IP address which will send you to you need to create a shortcut link to the following: (or if you have not enabled https on your switch). I can’t give guarantees other than that, but for now that does work. At the moment that I wrote this blog post that was Java 1.8.0.121. It’s OK to use the most recent Java version available. Manage Your Brocade Fibre Channel Switch with recent Java & browser versions Well not all of them, but it can be done with IE 11 and Firefox 52.0.1 (at the time of writing).Īnother solution is to use the CLI naturally.
#How to enable web access to brocade san switch how to#
We’ll show you how to get GUI access to your FC switches without needing to do that so you can manage your Brocade Fibre channel switch with recent Java & browser versions. With the default setting and links this will give you some headaches and some solution require you to keep older and insecure browser or java versions installed. That station needed to be used to manage some aging Brocade fibre channel switches. The guest was also Windows Server 2016 (desktop install). Read more in the Brocade admin guide.I was in the process of setting up a new jump server a management station server virtual machine on Windows Server 2016 Hyper-V. If not you can amend them as followsġ Before adding into a new port mapping you must remove a port from its existing mapping ag -mapdel N_Port “f_port1 f_port”įor example ag -mapdel 0 "15 16" F_Port to N_Port mapping has been updated successfullyĢ Create the new port mappings -mapadd n_portnumber f_port1 f_port2įor example ag -mapadd 17 "1 2 9 10" WARNING: Mapping F_Port(s) to this N_Port may cause the F_Port(s) to be disabledį_Port to N_Port mapping has been updated successfully If you are happy with the default port mapping you are good to go.
![how to enable web access to brocade san switch how to enable web access to brocade san switch](https://www.computernetworkingnotes.org/images/cisco/ccna-study-guide/csg76-02-assign-static-ip-on-server.png)
Please backup yourĭo you want to continue? (yes, y, no, n): yĥ Check access gateway mode is enabled as expected ag -modeshow Access Gateway mode is enabledĦ To see how the automatic port mapping has been configured run ag -mapshow N_Port Configured_F_Ports Static_F_Ports Current_F_Ports Failover Failback PG_ID PG_Name Including zoning configuration, FAWWN configuration and security database. Please check Access Gateway Administrator's Guide before proceeding.Įnabling agmode will remove all the configuration data on the switch You can check this by running switchshow and checking the modeĤ Enable access gateway mode ag -modeenable WARNING: Access Gateway mode changes the standard behavior of the switch. It is important to note that all zoning information on the switch will be lost.ġ Backup the current config of the Brocade switchĢ Check the switch is in native mode = 0. To put the switch in access gateway mode follow these steps.
![how to enable web access to brocade san switch how to enable web access to brocade san switch](https://i1.wp.com/s5.postimg.cc/o3dl249yf/2017-03-30_9-36-01_zpsm1k70yvj.png)
That’s the theory, lets walk through the steps to implement access gateway mode.īefore you start you need to make sure the upstream switch to the access gateway (AG) switch will connect to has NPIV enabled.Ģ If necessary enable for NPIV using portcfgnpivport Configuring access gateway mode You will cable the hosts into the F ports and the N ports will be connected to the upstream switch. When you enable access gate way mode a number of ports will automatically be designated as N ports and the rest F ports. This is a way to add more ports to your fabric without the complexity of additional switches containing zone configurations. Brocade switches enabled in access gateway mode act as an extension of the existing fabric, they have no zoning configuration on themselves and all traffic is transferred over uplink ports to a upstream switch containing the zoning information.